Helmholz 700-993-1AA01 OPTopus, PROFIBUS Optical Link, SMA, 650 nm, POF/PCF

Helmholz 700-993-1AA01 OPTopus, PROFIBUS Optical Link, SMA, 650 nm, POF/PCF

代码: 700-993-1AA01
品牌: Helmholz

The OPTopus PROFIBUS optical link is a full PROFIBUS repeater with integrated FO interface. It enables PROFIBUS transmission rates from 9.6 kbps to 12 Mbps with automatic transmission rate detection

Due to the optical signal transmission, it offers complete electrical isolation between the PROFIBUS participants and PROFIBUS subnets. Another advantage of OPTopus is the insensitivity to EMC influences.
Due to the compact design, no additional space is needed in the control cabinet, as it can be used instead of a PROFIBUS connector and is simply plugged into a participant on the PROFIBUS network.
No separate power supply is required, as the OPTopus uses the 5 V power supply, which every PROFIBUS device makes available for the terminating resistor.
The transmission signals are converted into optical signals by the OPTopus and are transmitted on the fiber-optic link; in addition, they are also regenerated with slope, level, and duty cycle.
The OPTopus is available with 3 different optical interfaces and is therefore perfectly compatible with existing transmission systems. It is suitable for POF** and PCF*-FO. For the short range up to 65 m, an optical transmission link can be established very quickly and without much effort using the POF**. For this purpose, the matching connector is included with the OPTopus. All that is needed is a standard POF**-FO. For longer distances up to 250 m, PCF* FO can be used.
The optical interface of the OPTopus sends in the visible range (650 nm red light), which allows an initial check of the optical transmission link without expensive instruments.
The OPTopus also offers the advantages of a normal repeater, such as: Bus extension, increasing the number of participants and expanding the system. Use in MPI networks is also possible.
As a special application option, the OPTopus allows the setup of stubs as separate segments. For this it can be plugged directly into the PG connection of an existing PROFIBUS connector.
For diagnostic purposes, the OPTopus has one Traffic and one Error LED for the PROFIBUS interface, along with one of each for the optical interface. In this way you are always informed about the bus state, and targeted troubleshooting is ensured.
There is also a Power LED that provides information about the operating state and the status of the terminating resistor.

General information
Order number700-993-1AA01
Article nameOPTopus, PROFIBUS Optical Link, SMA, 650 nm, POF/PCF
Scope of deliveryOPTopus, instructions, POF connectors
Dimensions (DxWxH)64 x 40 x 17 mm
WeightApprox. 40 g
PROFIBUS interface
Number1
ProtocolPROFIBUS-DP
Transmission rateMax. 9.6 ... 12 Mbps, autom. detection
ConnectionSUB-D connector, 9-pin
Optical interface
Wavelength650 nm
Numerical aperture of the transmitting diode0.50
Integrable optical power | receiver sensitivity POF¹ 980/1000 μm-7.5 dBm/-20 dBm
Integrable optical power | receiver sensitivity PCF¹ 200/230 μm-18 dBm/-22 dBm
Overdrive limit of the receiver-3 dBm
Bridgeable distance POF¹ 980/1000 µm (160 dB/km)0 … 65 m
Bridgeable distance PCF¹ 200/230 µm (10 dB/km)0 … 250 m
Status indicator3 LEDs, 4-color
Voltage supply+ 5 V DC
Current drawtyp. 100 mA with DC 5 V
Ambient conditions
Ambient temperature0 °C … +60 °C
Transport and storage temperature-25 °C … +75 °C
Pollution degree2
Protection ratingIP20
CertificationsCE
CE
RoHSYes
REACHYes



Helmholz 资料表

国家与语言 文件名 下载链接
United States (English) Helmholz-EN_42334.pdf 下载

请求报价